• 歡迎進入恒能環保能源設備有限公司

    熱線電話

    0531-69953988

    分類導航
    產品展示
    聯系我們
    山東恒能環保能源設備有限公司

    聯系電話:18678860671

    服務熱線:0531-69953988

    聯系地址:濟南市高新區舜華路2000號舜泰廣場9號樓南樓201室

    沼氣脫硫裝置中環境注意事項

    首頁- 新聞資訊 > 公司新聞 > 2021-12-21

    濕式除塵的優點是易于維護,通過配制不同的除塵劑,可以同時達到除塵和脫硫(脫硝)的效果。缺點是除塵液需要處理,可能導致二次污染。根據風量設計或選擇袋式除塵器時,一般不允許在風量超過規定風量的情況下運行,否則容易堵塞濾袋,縮短使用壽命,大大增加壓力損失,也降低除塵效率。但風量不宜過大,否則會增加設備投資和占地面積。
    The advantage of wet dedusting is easy maintenance. By preparing different dedusting agents, the effects of dedusting and desulfurization (denitration) can be achieved at the same time. The disadvantage is that the dedusting liquid needs to be treated, which may lead to secondary pollution. When designing or selecting the bag filter according to the air volume, it is generally not allowed to operate when the air volume exceeds the specified air volume, otherwise it is easy to block the filter bag, shorten the service life, greatly increase the pressure loss and reduce the dust removal efficiency. However, the air volume should not be too large, otherwise the equipment investment and floor area will be increased.
    目前使用的PPS濾料有很多。溫度是170℃。對于袋式除塵器,使用溫度與除塵效率的關系不明顯,與靜電除塵器不同。對于靜電除塵器來說,溫度的變化會影響粉塵的比電阻和除塵效率。玻璃鋼的長期耐溫性較差。玻璃鋼一般不能長期高溫使用,一般聚酯玻璃鋼在50℃以上強度會明顯下降,一般只能在100℃以下使用。當溫度超過60℃時,通用環氧玻璃鋼的強度明顯下降。
    生物脫硫
    There are many PPS filter materials used at present. The temperature is 170 ℃. For bag filter, the relationship between service temperature and dust removal efficiency is not obvious, which is different from electrostatic precipitator. For electrostatic precipitator, the change of temperature will affect the specific resistance of dust and dust removal efficiency. FRP has poor long-term temperature resistance. FRP generally cannot be used at high temperature for a long time. Generally, the strength of polyester FRP will decrease significantly above 50 ℃, and it can only be used below 100 ℃. When the temperature exceeds 60 ℃, the strength of general epoxy FRP decreases obviously.
    但可選用耐高溫樹脂,可將長期工作溫度保持在200~300℃。玻璃纖維增強塑料(FRP)層間剪切強度層間剪切強度由樹脂承擔,因此比較低。膜脫硫除塵器的清洗孔應位于管道的側面或上部,所有清洗孔必須嚴密不透氣。如果有漏氣,清洗孔上游管道內的流速會降低,積塵會更加嚴重,導致吸塵孔的排氣量減少。因此,在玻璃鋼脫硫除塵器的日常維護工作中,一定要注意細節。
    However, high temperature resistant resin can be selected to maintain the long-term working temperature at 200 ~ 300 ℃. The interlaminar shear strength of glass fiber reinforced plastics (FRP) is borne by resin, so it is relatively low. The cleaning holes of membrane desulfurization dust remover shall be located at the side or upper part of the pipeline, and all cleaning holes must be tight and airtight. If there is air leakage, the flow rate in the pipeline upstream of the cleaning hole will be reduced, and the dust accumulation will be more serious, resulting in the reduction of the exhaust volume of the dust suction hole. Therefore, attention must be paid to details in the daily maintenance of FRP desulfurization and dust collector.
    實際運行中,由于沼氣脫硫裝置生產設備的間歇運行以及一些未考慮的因素,粉塵也會沉積在管道中,越積越厚,一時難以清除。
    In the actual operation, due to the intermittent operation of the production equipment of the biogas desulfurization unit and some factors not considered, the dust will also be deposited in the pipeline, the more accumulated and thicker, which is difficult to remove at the moment.
    我們一直在堅持分享的路上沼氣脫硫http://www.rfidjournal.cn真正為您解決您所需要的問題.
    We have been insisting on sharing http://www.rfidjournal.cn Truly solve the problems you need

    相關產品 我們的存在,是為了更好的服務于沼氣等可燃氣體凈化及利用行業
    国产免费破外女真实出血视频,性欧美黄aaaaa片,欧美成人午夜免费全部完中文版,黑色丝袜无码中中文字幕,午夜理论片福利在线观看